Running the 20 t excavator

The camp's digger, from the first lever movement to loading a truck: what each stick does, how to drive on the tracks, reading the dig display, and why the arm sometimes stops.

Level
◆ Beginner
Reading time
5 min read
Steps
7 steps
Updated
Updated Nov 22, 2026
Running the 20 t excavator: what this guide shows

You'll need: The 20 t crawler excavator (every new site has one at the camp).

The 20 t crawler excavator is the machine you'll spend the most time in. It has a 5.7 m boom, a 2.9 m stick and a 1.0 m³ bucket, two boom cylinders working at 35 MPa, and two pumps sharing about 410 litres a minute. The house swings at up to 11 rpm. Nothing in it is animated: every movement is oil pushing a cylinder, so it moves the way a real one does, and it can run out of strength.

Step 1: Climb in and get comfortable

Walk to the cab door and press Y (Enter). Click the right stick (F) to switch between the cab and the outside view. Outside, the D-pad turns the camera round the machine and up and down (or orbit with the mouse), and clicking the left stick (or the mouse wheel) brings the camera nearer or further.

Step 2: Learn the four arm movements

Try each one on its own, slowly, before you combine them:

  • Left stick left / right (A / D) swings the whole house round on the tracks.
  • Left stick forward / back (W / S) pushes the stick (the outer arm) out, or pulls it in towards you.
  • Right stick forward / back (K / I) raises or lowers the boom (the big arm).
  • Right stick left / right (J / L) curls the bucket in, or opens it to dump.

The sticks are proportional: push a little for a slow, gentle movement. The two pumps share their oil between every function you move, so moving three things at once makes each of them slower than moving one.

Screenshot neededthe excavator from outside with the boom, stick and bucket labelled, arm half raised

Step 3: Drive on the tracks

Each track has its own pedal, like the real machine: LT drives the left track forward and LB back; RT drives the right track forward and RB back. On the keyboard: Q / Z for the left, E / C for the right.

  • Both forward: drive straight ahead.
  • One forward, the other still: a gentle turn.
  • One forward and the other back: turn on the spot.

Step 4: Dig your first bucket

  1. Lower the boom until the bucket's teeth touch the ground in front of you, with the stick pushed out.
  2. Pull the stick in towards you while curling the bucket. Lift the boom a little as you go to keep the teeth at the depth you want.
  3. Curl the bucket fully once it's full, then raise the boom to lift it clear.

The bucket fills with real soil: topsoil, clay, gravel and sand all cut, spill and pack down differently. Gravel pours; clay holds together.

A full bucket of gravel
A full bucket of gravel

Step 5: Load a truck

Park the dump truck beside you, within reach of the swing. Dig a bucket, raise the boom so the bucket clears the side of the truck's body, swing over the middle of the body and open the bucket to tip. It takes a handful of passes to fill the truck. Spread the loads front to back so the truck sits level.

Step 6: Read the dig display

Hold View (or press F1) to show the dig display. On the keyboard each press of F1 goes from off, to the hydraulics, to the hydraulics with the ground under the teeth, and back to off. It shows, for every function:

  • how far you're asking it to move and how fast it's going,
  • the oil pressure in its cylinder (colour coded) and the force,
  • the share of the pump's oil it's getting,
  • STALL when a cylinder is pushing as hard as it can and not moving, and END when it's at the end of its stroke.
Screenshot neededthe 20 t excavator's dig display (hold View / F1) while digging, showing STALL on the boom line

Step 7: Why the arm stops (stalling)

The arm can only push as hard as its cylinders can at 35 MPa. Dig too deep, try to pull the stick through a bank that's too hard, or try to lift more than the machine can hold, and the cylinder stalls: the lever is pushed but nothing moves, and the dig display shows STALL. This isn't a bug. Back off: lift the boom a little, take a thinner slice, or curl the bucket out of the cut and start again.

If the machine starts to tip forward when lifting, lower the load. The machine's own weight is what holds it down.

Lifting with the chain

The excavator carries a hook on its bucket linkage. Bring it over a lifting point (the wash plant's lifting lug or tow ring, for example) and press A (H) to hook a short chain on. The load hangs on the arm: what you can lift is what the cylinders can hold, and how much the machine can hold down before it tips. Press A (H) again to unhook once the load is resting on something: the game won't let go of a load that's still hanging. Moving the wash plant this way has its own guide.

Is what you're looking for not here?

Tell us what you'd like explained and we'll write a guide for it. You'll need to sign in first.

Request a guide: sign in

Request a guide

The more you tell us about where you got stuck, the better the guide.