Running the articulated trucks

Get the 25 t or 40 t articulated dump truck onto your site, drive it off-road, reverse with the pedals, tip the load, use the diff locks and the retarder, and pull a stuck machine out with its front winch.

Level
◆ Beginner
Reading time
4 min read
Steps
6 steps
Updated
Updated Nov 21, 2026
Running the articulated trucks: what this guide shows

You'll need: Nothing to buy: both are free to try from the pause menu's DEMO VEHICLES.

The articulated dump trucks go where a road truck can't. They steer by bending in the middle, the back half rolls on its own hitch so all six wheels stay on rough ground, and every axle is driven. There are two:

25 t articulated truck40 t articulated truck
Body15 m³ heaped24 m³ heaped
Payload24 t39 t
Engine230 kW400 kW
Pairs withthe 36 t excavator (6 or 7 passes)the 75 t excavator (7 or 8 passes)

Both have a 6-speed automatic box, diff locks on every axle and a recovery winch on the front bumper. The body's tail is open: there's no tailgate to unlock.

The 40 t articulated truck loaded
The 40 t articulated truck loaded

Step 1: Put one on your site

The articulated trucks aren't for sale yet: they're demo vehicles, free to try. Press Menu (Esc), pick DEMO VEHICLES, and choose 25 T ARTICULATED DUMP TRUCK or 40 T ARTICULATED DUMP TRUCK. It's set down on clear ground in front of you. You can have one of each on a site.

To get rid of one, open DEMO VEHICLES again and pick it from the ON THE SITE list, then TAKE IT AWAY. Anything in its body is tipped onto the ground where it stood.

The DEMO VEHICLES menu
The DEMO VEHICLES menu

Step 2: Drive it

Climb in with Y (Enter). RT (W) is the throttle and LT (S) the brake; the left stick (A / D) steers. Press A (Space) to let the parking brake off: the bottom line shows Parking brake: ON or off.

The gearbox picks its gear by road speed, and the bottom line shows the gear and your speed. Off the throttle above walking pace, the transmission's retarder slows you down by itself (the line shows retarder N%), which keeps the brakes cool on long grades. The 40 t has a much stronger retarder for the long grades down.

Step 3: Reverse

Stop and hold the brake. When you're stopped, the bottom line says Stopped: hold the brake for reverse. After a moment it goes into reverse and the line reads Reverse: brake pedal backs up; throttle brakes, then forward. So in reverse, LT drives you backwards and RT brakes. Stop and hold RT to go forward again.

Step 4: Get loaded and tip

Stop beside the excavator or loader with the parking brake on and let them fill the body. Spread the load front to back.

At the dump spot, stop on ground that's as level as you can find, set the parking brake, and hold RB (R) to raise the body. The bottom line shows the body angle while it tips. The load slides out of the open tail onto the ground. Hold LB (F) to lower the body again before you drive off.

Step 5: Use the diff locks

In mud or soft ground one wheel can spin while the others do nothing. Press B (X) to lock the differentials on every axle and between the axles, so all six wheels turn together. The line shows Diff locks: ON. Press B again to unlock them on firm ground.

Step 6: Pull a stuck machine out with the winch

Each articulated truck has a winch on its front bumper with 30 m of wire rope. The 25 t's pulls about 196 kN and the 40 t's about 265 kN.

  1. Drive the truck's nose to within about 28 m of the front or back of the stuck machine. The bottom line offers Connect winch with the machine's name, which end, and how far.
  2. Press D-pad left (H) to hook the line on.
  3. Hold D-pad up (U) to reel in. The line pulls the stuck machine towards the truck (and the truck towards it). If the line reads STALLED, it's pulling as hard as it can: back the truck up gently or get someone to drive the stuck machine while you pull.
  4. Hold D-pad down (J) to pay out. D-pad right (K) is the free-spool clutch: the line runs off freely as it's pulled.
  5. When the machine is out, pay out until the line is slack and press D-pad left (H) to unhook. The game won't unhook a line that's still under load.

The line stays hooked whatever you do, even if you climb out and go and drive the stuck machine yourself.

Screenshot neededthe 25 t articulated truck with its winch line hooked to the back of a stuck excavator, bottom line showing "Reel in winch (hold)"

Is what you're looking for not here?

Tell us what you'd like explained and we'll write a guide for it. You'll need to sign in first.

Request a guide: sign in

Request a guide

The more you tell us about where you got stuck, the better the guide.